We installed our britax boulevard car seats last night .... rear facing. They are basically vertical, bo recline. My husband says that's right because the twins are toddlers. I think it just looks really awkward and that it will be hard to buckle them in.
Any advice from others who use this car seat? Thanks!!!!!
nectarine / 2018 posts
@meadow: do you have the G4 or clicktight boulevard? The clicktight a have a ton of recline options so very easy to change. The G4 only has one rear facing recline (and two forward facing). If it's a G4 I would make sure it is on the rear facing recline - which is position 3. If it's on the right setting try to install while pushing where lo's bottom would go, that can manipulate the seat a bit. But it will still be relatively upright, especially depending on the slope of your seats.
persimmon / 1272 posts
@catgirl: clicktight......so yes many options. We had it in tbe middle, then all the tightening made it fully upright. DH said leave it & I think it seems too upright.....
We have to redo the install to change the recline, so looking for input before in push the issue....haha
nectarine / 2018 posts
@meadow: Okay, so 7 recline options. As long as the indicator is in the rear facing section you are fine, and for an 18 month old it can definitely be pretty upright - but it doesn't have to be upright. It's all about preference, what your kid likes, and how much space you want to seat to take up in the car. Before installing always recline more than you think you will need because installation will make it change.
pear / 1521 posts
@meadow: I would definitely fix it since it's a clicktight! Shouldn't be too tough. Make sure you unbuckle the seat belt before trying to turn the dial, it's much easier that way.
pear / 1521 posts
Oh and if you have them super upright any time they fall asleep in the car their heads will fall straight forward which always looks so sad and uncomfortable to me! Might as well have them more reclined to prevent that since you can.
persimmon / 1272 posts
@petitenoisette: thanks! We installed LATCH since kiddos are <25lbs. Good point about the head bob! Haha
We'll give it a try this week and see how it is to put them in I guess....
honeydew / 7463 posts
@meadow: Maybe I’m wrong or misunderstanding but I don’t think how tight the install is should impact how upright the seat is, especially if it’s an adjustable incline.
Like if the install is changing the incline, I would wonder if it’s correct?
Full disclosure I am far from a car seat expert aside from installing ours over and over. Maybe post a pic? Or ask car seats for Little’s on Facebook?
nectarine / 2288 posts
We also have a click tight Boulevard. Install always alters the recline a bit because the seat slopes.
I'd pull them out and adjust the incline if you think your littles will be uncomfortable. Make sure the level bubble thing is at the correct area for a toddler. And I would install with the seatbelt, it's insanely easy and zero reason to use the harder install with the latch in my opinion. The easy seatbelt install was one of the huge reasons I went with this seat
nectarine / 2018 posts
@meadow: I would be very hesitant to install with the latch with the clicktight seats. They were designed specifically for easy seat belt install and only included lower anchors because they were legally required to. It is very easy to damage the clicktight panel when uninstalling if you have used the latch.
@SweetiePie: I think it's more that whatever setting you pick it will look more reclined before it's tightened. That's pretty common of all seats.
persimmon / 1272 posts
Haha....took our first trip to the grocery store this afternoon........no way!!! I had to lower DS from above the headrest.....hahaha
nectarine / 2400 posts
@meadow: yah no way I would use latch that’s the best part about clicktight!
ETA my husband and I both agree we will only buy clicktight from now on it is absolutely worth the money and has literally made moving car seats beyond painless
nectarine / 2047 posts
We have a britax boulevard clicktight as well and I usually put it one or two positions more reclined than I think is necessary bc the angle does change due to the seats sloping as @MamaBear87: said. I watched a video that showed reclining the back seat as much as possible if able and moving the front seat forward as much as possible and then installing the seat. So you stand in the car with your belly against the back of the car seat pushing in while clicking the seat belt and pushing down on the seat, then bring the back seat back up into the upright position. I get a rock solid install every single time doing it that way. It’s amazing. I will never use latch with these seats bc the clicktight seatbelt installation is so so good.
| Today | Monthly Record | |
|---|---|---|
| Topics | 0 | 1 |
| Posts | 1 | 1 |
Ask for Help
Make a Suggestion
Frequently Asked Questions
Bee Levels
Acronyms
Most Viewed Posts
Hellobee Gold
Hellobee Recipes
Hellobee Features
Hellobee Contests
Baby-led Weaning
Bento Boxes
Breastfeeding
Newborn Essentials
Parties
Postpartum Care Essentials
Sensory Play Activities
Sleep Training
Starting Solids Gear
Transitioning to Toddler Bed
All Series
Who We Are
About the Bloggers
About the Hostesses
Contributing Bloggers
Apply to Blog
Apply to Hostess
Submit a Guest Blog
Hellobee Buttons
How We Make Money
Community Policies
- Google Plus
- Stumbleupon
- Twitter
- Facebook
- Pinterest
- Favorite0
12 comments